Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Recommended Posts

Posted

My motor mounts let go the other day. Red fluid started dripping from both sides of the rear of the car. Maybe two ounces each. They are easy to replace.

You have to remove the airbox for the right mount and get the air pump out of the way for the left mount.

Two bolts hold the top of the mount and one nut at the bottom. If you decide to torque the bottom nut, it is 63 ft lbs.

I think it is an 19mm socket. Deep if available. The top stuff requires a 10mm, 13mm and a 7/64 torx or metric equivelant for the MAF. When you have the new mounts installed and just snug, take the car off the jacks so it is sitting on the ground with no support, then

tighten the two top bolts and bottom nut. Check the exhaust tips and they should be even.

When car is suspended on four jack stands, you need to support the engine with a hydraulic jack so as to take the weight off of the mounts. This will make the old motor mounts pull right out. You might have to play with the left mount to wiggle it out and around the air pump that

you semi-removed by removing the two bolts and one nut. OEM mounts are around $100.00 each thru discount stores.

You might as well clean the throttle body while you have the air box removed.

  • Upvote 1
Posted

Did you notice any improvement compared to the old mounts before they let go? Or do the mounts work properly until they fail?

Posted (edited)

Please be careful supporting the engine with a jack. You have to do it in the right place.

There are plenty of other DIYs out there that describe this process in more detail, including safe engine jacking locations.

The order of steps in the original post is a little off, so please read and be careful.

Support the engine SAFELY AND FIRST before you touch the mounts.

Do not jack directly under the sump plate (unless you know how to do that safely). For example, do not just put the jack's cup directly under the plate.

Edited by logray
  • Upvote 1
Posted

Did you notice any improvement compared to the old mounts before they let go? Or do the mounts work properly until they fail?

I didn't notice anything until mine failed.

Posted

I didn't notice any difference. Psychologically it did but my car runs better after washing it too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.