Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

Problems at normal temp, rough idle, clicking.....

chu77

By chu77
in 986 Series (Boxster, Boxster S)

 Share

Recommended Posts

chu77 Member

chu77

Posted
Posted (edited)

I just got a 1999 boxster, 2.5L, 5spd, it runs great until it hits 180F.

At 180F

1) Idle is rough, drops below 400 and back to 1100 everytime after I rev it.

2) Stalls at fiction point

3) Idle will produce oil light below 400rpm and somtimes stall

4) Clicking noise rear right side, almost a rattle in 1 and 2 gear

I've cleaned the IACV, check the oil levels, added octane boost

Is there a way to reset the computer?

Or is this another RMS or IMS problem? But the car runs perfect below 180F.............

Edited by chu77
  • Moderators
RFM Member

RFM

Posted
  • Moderators
Posted

Try to catch the fault codes with a diagnostic tool, disconnecting the battery will reset the DME ( watch the radio code ), it is probably not RMS or IMS.

chu77 Member

chu77

Posted
  • Author
Posted
Try to catch the fault codes with a diagnostic tool, disconnecting the battery will reset the DME ( watch the radio code ), it is probably not RMS or IMS.

Got code P1691 which is a short for the cel light. I checked the light and it was not burned. Are there a fuse for the CEL?

Also the engine is very hard to start once warmed up, I have to give it half gas in order to have it catch.

chu77 Member

chu77

Posted
  • Author
Posted
P1691 Check Engine Malfunction Indication light (MIL) - Open Circuit

Potential cause:

- Break in wiring.

Are you sure that is the only code?

Yeah that's the only code, but now I hear the clicking noise at cold temps too. Sounds more like a clunking noise now that I read up on more threads about the IMS. I'm also getting some oil leaks (2-3 drops per day) from the RMS area.

From what I know of the car's history it's been sitting for 2-3 years. I drove it 2k miles from U.S back to Canada and the engine still felt powerful but had this problem about 1k miles into the drive home.

chu77 Member

chu77

Posted
  • Author
Posted (edited)

Well I was making a video for you guys to take a look and the engine quited on me. I tried to rev it to make the clicking noise and sounds like something seized and the engine stalled......

Any ideas? Here's the video

(Link to youtube, did it worked?)

Edited by chu77
chu77 Member

chu77

Posted
  • Author
Posted (edited)
does the car start now after this incident?

No start, I've changed the oil, found lots of small sandy metal and the oil color was dark grey and thick (lots of metal in there)

Put new oil in the boxster, still no start. I tried push starting it and no luck.

Also there is no "Hummmm" before I start the car. Isn't that the fuel pump or the oil pump?

Edited by chu77
Sputter Member

Sputter

Posted
Posted

If you're right when you say "lots of metal" and "dark grey and thick", flat bed it to a shop. Don't be trying to run it at this point.

How did the oil look when you picked the car up?

You say it started doing this on the way back from buying it?. When you did the PPI prior to sale, what did the report say?

I don't want to scare you more than you likely are. A porsche shop will give you a much clearer picture.

Good luck man.

does the car start now after this incident?

No start, I've changed the oil, found lots of small sandy metal and the oil color was dark grey and thick (lots of metal in there)

Put new oil in the boxster, still no start. I tried push starting it and no luck.

Also there is no "Hummmm" before I start the car. Isn't that the fuel pump or the oil pump?

1schoir Member

1schoir

Posted
Posted
Engine is seized, looks like I'm going for a 3.4L swap. Anyone have one for sale? lol

Sorry to hear the bad news. Looks like you are trying to turn that negative into a positive though.

Try member "tholyok". I think he had one for sale recently.

Also, you could look at Mike Focke's Boxster Pages. He's got a good list of recyclers that deal in engines on a regular basis.

Regards, Maurice.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.