Jump to content

Welcome to RennTech.org Community, Guest

There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.

Here are some of the features available - once you register at RennTech.org

  • View Classified Ads
  • DIY Tutorials
  • Porsche TSB Listings (limited)
  • VIN Decoder
  • Special Offers
  • OBD II P-Codes
  • Paint Codes
  • Registry
  • Videos System
  • View Reviews
  • and get rid of this welcome message

It takes just a few minutes to register, and it's FREE

Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)

  • No ads - advertisements are removed
  • Access the Contributors Only Forum
  • Contributing Members Only Downloads
  • Send attachments with PMs
  • All image/file storage limits are substantially increased for all Contributing Members
  • Option Codes Lookup
  • VIN Option Lookups (limited)

JFP in PA

Moderators
 View Profile  See their activity

  • Posts

    8,732

  • Joined

  • Last visited

  • Days Won

    199

 Content Type 

Everything posted by JFP in PA

  1. JFP in PA
    Does that purge valve stay closed (hold vacuum or pressure)? You check the fuel pressure by attaching a fuel pressure test gauge to the test port on the fuel rail, and then check your pressures running and shut off. Can you use your OBD device to read fuel trims?
  2. JFP in PA
    I'd start by checking the fuel pressure, then looking at the EVAP purge valve (they can often be cleared with a quick blast of compressed air). I would also look at the fuel trims. I have no idea why they list the MAF, it is not even mentioned in the factory OBD II manual for the car decision tree for diagnosing the codes. Once of the biggest issues with a generic OBD II scanner is they often list fixes that may have worked on a Ford Fiesta, but totally do not pertain to your Porsche. For example, while they do point out valid possibles, I have no idea how replacing a brake booster is going to help an overly rich A/F mixture issue...………..
  3. JFP in PA
    Yes, you went after the wrong thing. Both codes indicate an overly rich condition that the system cannot compensate for, possibly from a high fuel pressure issue, leaking injectors, or a stuck EVAP purge valve. Lesson here is to learn what the codes are telling you before reaching for a credit card...…………..
  4. JFP in PA
    Welcome to RennTech You can start by posting this in the correct forum section "Lost Radio Code - post your request here"...…………..
  5. JFP in PA
    You need to take equal amounts of both sides of the gap to obtain the final clearance. We use a Total Seal unit to do this: But you can use a simpler hand tool like this to get to the same place:
  6. JFP in PA
    The immobilizer under the seat is coded to your keys and the DME, it cannot simply be changed out, it requires coding with a PIWIS or PST II.
  7. JFP in PA
    Welcome to RennTech On cabriolets, the number 2 relay panel is mounted to the rear of the roll over protection frame. You need to put the top in the "service" position to gain access to it.
  8. JFP in PA
    I would look at the O2 sensor voltages before and after the main cats, and would also check the fuel trims. A lamda of 1.0 would have the engine running at an air/fuel ratio of 14.7:1; if the lamda is above 1.0, the engine is running lean, if below 1.0 the engine is running rich. You have a lean condition, which could be as simple as a vacuum leak.
  9. JFP in PA
    Just get the factory unit and be done with it. Piersburg is supposed to be a supplier to Porsche, but the units I have seen in the aftermarket do no look the same.
  10. JFP in PA
    +1
  11. JFP in PA
    I have no idea where you subwoofer is, how about a photo?
  12. JFP in PA
    In relay panel #2, under the rear parcel trim panel, behind the rear seat backrest.
  13. JFP in PA
    As I mentioned earlier, we only use the factory pump. Your old cap sounds beat, the new cap is about right.
  14. JFP in PA
    Welcome to RennTech You are not the first, nor will you be the last to run into problems trying to mate unknown after market technology in the Porsche MOST and CAN Bus technologies. Even some "top of the line" audio systems have problems with this. MOST is fiber optics, and CAN Bus is a single twisted pair networking format. Good luck.
  15. JFP in PA
    Many OBD II scanners do not successfully read Porsche codes, particularly for something like the PDK. You need a Porsche specific tool (Durametric, PIWIS).
  16. JFP in PA
    Welcome to RennTech I think you will find that this device is no longer made. Try looking for a used one, or fabricate one yourself.
  17. JFP in PA
    Sometimes it is the simplest things. Glad you got it sorted, now go get a factory pump.........
  18. JFP in PA
    Chance would be a fine thing. $5-10K would be an excellent deal, the annual lease costs for a current PIWIS system is $20K per year...……..
  19. JFP in PA
    0.032 is more than a little lose for this bore size, the old rings are closer to correct. To make sure I understand where you are, you cannot get the piston into the bore with the new rings on it, correct? If so, what kind of ring compressor are you using? And where did you source the replacement rings from?
  20. JFP in PA
    Checking the coolant for combustion by products was a good idea, you have removed another possibility. Now, about that water pump...…...
  21. JFP in PA
    I called two wholesalers that handle Gates and aske them to look, one said metal, the other composite. I think the Gates is a 50/50 proposition.
  22. JFP in PA
    Welcome to RennTech What is the end gap of the ring in question when inserted alone into the cylinder bore at a depth of about 1 inch below the deck?
  23. JFP in PA
    It is not a matter of personal concerns, it is on the advice of legal counsel. What other website do or do not do does not concern me, but we cannot allow either this site, or me personally, to become the "deep pockets" in the legal equations resulting from actions beyond our control.
  24. JFP in PA
    See my response above.
  25. JFP in PA
    Let's start with the basics: Year and model of the car, and what code are you seeing?
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.